Turo Vortex Pumps T

Turo^® Vortex Pumps with a completely open spherical channel. Only 15% of the pumped fluid comes into contact with the impeller. Around the world, thousands of pumps have proven themselves with decades of excellent service.

Applications

Municipal and industrial wastewater
Every kind of sludge
High concentrations of fibrous suspensions
Chemical and crystalline suspensions
All viscous materials
Numerous abrasive and corrosive fluids

Features

Gentle pumping of sensitive liquids and sensitive crystal structures
Special volute casing, tuned to the hydraulics

Please describe to us your requirements profile and a description of the fluid to be pumped.

Facts & Figures

Nominal dimensions:	DN 32- 200 mm
	1 1/4 - 8"
Capacity:	up to 140 l/s
	2220 US gpm
Discharge head:	up to 140 m,
	460 ft
Discharge head:	up to 30 bar / 440 psi
Operating	up to 180 °C / 355 °F
temperature:

Advantages

Freedom from clogging by solids
High, sustained efficiency
Large, open spherical channel
Reduced wear
Low life cycle costs (LCC)
Long service life (MTBF)
Economic storage, thanks to its modular design

Additional information on Vortex Pumps

Models

Dry mounted
Horizontal and vertical

Wet mountedShaft pumps
Cantilever pumps
Submersible pumps

In practice

Wastewater pumping station 2 No. Turo^® T 71-80 pumps connected in series and installed in vertical and horizontal orientations. Hydraulics mutually interchangeable, thanks to modular support feet.

Raw water inflow pumping station for a wastewater treatment plant: 2 Turo^® T 81-150 SG8 LB4B shaft pumps for peak load support of the screw pump station. Hydraulics in abrasion resistant HG 15.3 hard cast iron.

Emile Egger & Cie SA l Route de Neuchâtel 36 l 2008 Cressier NE (Schweiz) l Tel. +41 (0)32 758 71 11 l Fax +41 (0)32 757 22 90 l Impressum / Disclaimer

Emile Egger & Cie SA l Route de Neuchâtel 36, 2008 Cressier NE (Schweiz)
Tel. +41 (0)32 758 71 11 l Fax +41 (0)32 757 22 90 l info@eggerpumps.com l www.eggerpumps.com

Turo® Vortex Pumps with a completely open spherical channel. Only 15% of the pumped fluid comes into contact with the impeller. Around the world, thousands of pumps have proven themselves with decades of excellent service.

Applications

Features

Facts & Figures

Advantages

Additional information on Vortex Pumps

Models

Shaft seal

Materials

Power range

In practice

Wastewater pumping station 2 No. Turo® T 71-80 pumps connected in series and installed in vertical and horizontal orientations. Hydraulics mutually interchangeable, thanks to modular support feet.

Raw water inflow pumping station for a wastewater treatment plant: 2 Turo® T 81-150 SG8 LB4B shaft pumps for peak load support of the screw pump station. Hydraulics in abrasion resistant HG 15.3 hard cast iron.

Turo^® Vortex Pumps with a completely open spherical channel. Only 15% of the pumped fluid comes into contact with the impeller. Around the world, thousands of pumps have proven themselves with decades of excellent service.

Wastewater pumping station 2 No. Turo^® T 71-80 pumps connected in series and installed in vertical and horizontal orientations. Hydraulics mutually interchangeable, thanks to modular support feet.

Raw water inflow pumping station for a wastewater treatment plant: 2 Turo^® T 81-150 SG8 LB4B shaft pumps for peak load support of the screw pump station. Hydraulics in abrasion resistant HG 15.3 hard cast iron.